Graffiti Remover Gal BareBrick/Stone/Mason
Quick Overview
- No shadows, no damage, no harsh scrubbing required.
- It may be used on painted surfaces as well as nature building surfaces after the first wetting surface with water.
- Pleasant smelling and nontoxic.
- Safe and effective to use on all types, and nature stone, stainless steel, trees, plastics, and playground equipment.
Show More
$82.15
$95.60
Graffiti Remover Gallon Bare Brick, Stone, Masonry
Bare Brick, Stone & Masonry Graffiti Remover is a highly effective, economical and biodegradable graffiti remover for all types of spray can paints, oil/ latex/ water based paint over spray, paint spill stains, grease, grime, smoke, and oil stains, as well as other marks on porous brick, stone and concrete surfaces including cinder block, split face block, and exposed aggregate.
* No shadows, no damage, no harsh scrubbing required.
* Pleasant smelling and nontoxic.
* Safe and effective to use on all types, and nature stone, stainless steel, trees, plastics, and playground equipment.
* It may be used on painted surfaces as well as nature building surfaces after the first wetting surface with water.
Coverage Guidelines
1 gallon of BBSM graffiti remover will remove approximately:
200 sq ft of typical graffiti on concrete, brick, block or masonry surfaces. 80 sq ft on sandstone, limestone and other soft absorbent surfaces (per 3 flood coat application).
Up to 1000 sq ft per gallon on painted/coated surfaces.
Exact coverage varies depending on type of stain and the porosity of surface material.
Bare Brick, Stone & Masonry Graffiti Remover (BBSM) is a highly effective graffiti remover for all types of spray can paints, oil, latex, water based paint over spray, paint spill stains, grease, grime, smoke, and oil stains
Equally effective on other marks such as porous brick, stone and concrete surfaces including cinder block, split face block, and exposed aggregate.
Features & Benefits
BBSM is economical and bio-degradeable.
BBSM Graffiti Remover is easily rinsed with a small pressure washer requiring very little rinsing water. Any resultant run-off is a readily biodegradable gray water soap that can be left to biodegrade, recycled or further diluted for use in gardens, etc.
Product Use Instructions
BBSM Graffiti Remover is applied to the surface with a nylon brush, broom or pump-up sprayer, 3 times at 3 minute intervals, liberally flooding the Graffiti with the product. For typical graffiti, approximately three minutes after the final application, pressure washer (hot water is best).
If one is not available then a stiff, nylon brush and bucket of water may suffice.Agitation, as you apply this product, can be of great assistance.
Continued experience with the product will enable the user to judge how many applications are necessary for varying surfaces and particular spray cans. On older/thicker graffiti, patience is the key. Keep the graffiti wet with the product, as long as possible before rinsing.
A pressure washer in this instance is used as a quick release rinse of the dissolved graffiti, and not the primary means of cleaning.
Ideally use 1500 - 2000 psi with a 15º or 25º fan jet at about 6 inches from the surface. When rinsing dissolved graffiti with a pressure washer try to remove a LITTLE of the graffiti from the bottom of the tag without wetting the whole area. If satisfied, then proceed to full scale.
Wash the whole area from top to bottom.
Noe: if the remover has not done its job, then no amount of ‘blasting’ will fix the problem.
Failures are usually a result of not flood coating adequately and not leaving product on long enough but they cannot be resolved by blasting too close or at higher pressures. Do not use ‘turbo’ type nozzles, or blast too close, as you may cause damage and will possibly only remove a small percentage more.
