Welcome to J. Racenstein Co  (201) 809-7500  |   Q & A  |   Help  |  Catalogs  |  About Us  |  Events
Orders over $50 enjoy Free Shipping with our Web Promotion.

ProTool Dual Pump Mounting Ready to Use

Item #: 150-823  UPC : 00669893023055

$185.50

$227.20

 
 
 Available Late June
This is an obsolete Item

Wall Mount Pump Plate Complete.

This aluminum wall mount pump plate frame comes ready to mount. All electrical equipment is pre-installed and wired up. Pump post are pre-installed and secured with jam nuts to prevent rattling loose. 

Red and black bus bars for power distribution from the battery. 

Two 40 amp circuit breaks are installed to protect the pump/pump controllers and pre-wired. 

All red and black wires have quick connects ready to add pumps. 

Intended to mount in a van, on a flat bed truck or trailer, the aluminum frame wont rust and is bleach safe.

Rivnuts are installed for easy installation of electrical equipment, breaker switches and pump controllers. 

Picture on left is configured for RODI setup ready for pumps and a controller. 

Picture on right is configured for Soft Wash setup ready for pumps and a metering system. Has the metering bracket added.

See the RODI Kits here:



For Pumping Water

For Softwashing

Soft Wash Full configuration example:

This plate works perfectly for a soft wash application. 

Aluminum is SH safe and wont rust. 

Optional bracket add on to mount soft wash metering system to this frame. 

(components are not included)

See the Soft Wash RODI Kit here:

RODI Full configuration example:

On the right the plate is mounted to a van divider wall. It has the pumps and pump controller added to the plate. 

Ready for RO boost and single operator. (Capable of running two poles off one line)

The plate dimensions are:

21in wide by 12in high,

  • The holes in the corner are 18in wide 1.5in in from the edge on the long side
  • The center hole is 10.5 in in from the edge on the long side
  • The holes are 11in apart on the short side.

The installation needs 4 to 5 inches above and below the plate to accommodate the pumps and allow for clearance of the hose connections. So a 22 wide by 22 high dedicated space would be sufficient

The plate dimensions are:

21in wide by 12in high,

  • The holes in the corner are 18in wide 1.5in in from the edge on the long side
  • The center hole is 10.5 in in from the edge on the long side
  • The holes are 11in apart on the short side.

The installation needs 4 to 5 inches above and below the plate to accommodate the pumps and allow for clearance of the hose connections. So a 22 wide by 22 high dedicated space would be sufficient



Proposition 65 requires businesses to provide warnings to Californians about significant exposures to chemicals that cause cancer, birth defects or other reproductive harm.  These chemicals can be in the products that Californians purchase, in their homes or workplaces, or that are released into the environment. By requiring that this information be provided, Proposition 65 enables Californians to make informed decisions about their exposures to these chemicals. Proposition 65 also prohibits California businesses from knowingly discharging significant amounts of listed chemicals into sources of drinking water. Proposition 65 requires California to publish a list of chemicals known to cause cancer, birth defects or other reproductive harm. This list, which must be updated at least once a year, has grown to include approximately 900 chemicals since it was first published in 1987. Proposition 65 became law in November 1986, when California voters approved it by a 63-37 percent margin.  The official name of Proposition 65 is the Safe Drinking Water and Toxic Enforcement Act of 1986.

The list of chemicals contains a wide range of naturally occurring and synthetic chemicals that include additives or ingredients in pesticides, common household products, food, drugs, dyes, or solvents. Listed chemicals may also be used in manufacturing and construction, or they may be byproducts of chemical processes, such as motor vehicle exhaust.  For more information visit www.p65warnings.ca.gov/