Welcome to J. Racenstein Company, LLC  (201) 809-7500  |   Help Center  |  Catalogs  |  About Us

Rotary Brush 39 inch (100cm) Water Powered

Quick Overview

  • Designed to clean solar panels, vinyl, and aluminum siding
  • It is a mobile, hand-operated unit designed to be controlled manually
  • Hydrokinetic brushes save considerable time compared to traditional brushes
  • Requirements: 580 psi at brush head max and 2.3 gallons per minute consumption

Show More
Item #: 159-136  MPN : HSLR10

$2,677.85

$2,857.40

 
 
 In Stock & Ready to Ship
This is an obsolete Item

Brush 39in Water Powered for Cleaning Large Surfaces

The rotating roller brush was designed and built to clean solar panels, vinyl and aluminum siding.
It is a mobile, hand-operated unit designed to be positioned and operated manually on the surface to be cleaned.
Rotary hydrokinetically brushes offer considerable time savings in the cleaning operation performed on solar panels and building surfaces when compared to traditional fixed brushes.

Requirements:
- 600 to 700PSI (40 to 50 BAR) pressure at brush head max
- 2.3 to 3 Gallons per minute (9 to 11LPM) consumption
Max. Water Temperature: 104° F (40° C)

For Pressure washing sizing the brush is the same usage as a #7 tip

Pressure washer:

Recommended Pressure Washer: 3 gallons per minute, 2500psi
 

Weight: 12.5lbs

32inch Rotating Brush Water Powered for Solar Panels

Rotating Brush User Manual






Instructions for Use:
  1. Connect the brush to the telescopic lance.
  2. Position the unit on the surface to be cleaned.
  3. Open the water valve on the telescopic lance.
  4. Begin cleaning the surface.
Stopping the Brush - Turning off the cleaning
  1. Close the telescopic lance’s valve.
  2. Turn off the water supply
  3. Open the telescopic lance’s valve to discharge the residual pressure.

Connecting to a Extension Wand

When using an Extension Wand that has an M22 Male Tip on the  end. Then to attach the water poered brush be sure to order a Female to Female M22 Fitting to connect the brush to the extension wand 

Specifications:

Width: 39 in. (1000mm)
Diameter: 5.9 in. (150mm)
Weight: 10 lbs (4.5Kg)
Bristle: 0.6 in.(15mm)
Attachment: M22 x 1.5mm Connector

CLEANING COATED OR PAINTED SURFACES
Using water on glued parts may cause them to become detached. Do not use the unit on wood floors or parquet that are not well-sealed.
Be careful when cleaning doors, parquet, painted surfaces or surfaces coated with synthetic products, and aluminum panels.
Before using the brush, we advise performing a test on a portion of the surface that is not in view, to prevent damage or alterations during cleaning.

PRODUCTS TREATED – HANDLED OR GENERATED
The Solar Panels treated with the brush should be comprised of modules with a maximum tilt of 35°.
Verify in the photovoltaic system’s operating manual the type of brushes that can be used for cleaning it, so as not to cause abrasions on the panels’ film.

It is important to avoid all operating situations that could cause repeated and unexpected stops of the brush’s rotation, such as those specified below:
- In the case of surfaces comprised of panels, the maximum distance between them must be 3 cm to prevent the unit from dropping into the empty space between one panel and the next.
- The surfaces must be as free as possible of protruding bodies such as long screws, brackets, and terminals, which could obstruct brush rotation or rip out its bristles.
- The unit is not designed to withstand heavy accidental impacts, such as those caused by being dropped, or those that are less intense but repetitive, such as those resulting from operating in stepped areas.
- It is also very important that the operating pressure not exceed the maximum value indicated in the “Technical Specifications” in order to prevent excessively high rotation speeds from causing premature wear of the unit’s mechanical parts.
- When not in operation, never allow the unit’s weight to rest on the rollers’ bristles so as not to bend them.

Regulator and Gauge

Use a Pressure Gauge to undestand the pressure at the brush

Install the Gauge on the water connector on the brush

Test Run your your pressure washer and supply water to the brush from your running pressure washer the PSI should be between 290 psi and 725 psi.

One you have your system setup at the correct pressure ytou can remove and store the gauge for future testing

Alway test again after a pressure washer has been worked on or should a different pressre washer is put in place to power the brush

NOTE:

If your pressure Washer is running the brush at more that 725PSI then immediatly stop the water flow.

You can try a smaller pressure washer or install and adjust a  Pressure Regulator to set the pressure to the suggested 600 to 650 psi to run the brush. (Max 725psi)


Regulator and Guage not included

Testing and Setting Water Pressure 

If your pressure washer is to big you will need to usea Pressure Regulator to control the Pressure - Target 600 to 650 PSI.

Here the gauge is installed 

Attached to the Pressure washer and run the brush, ig you are between 550 and 650psi you are good to go.

Attach a Pressure Regulator and Test, Set PSI

If the pressure is more than 725 PSI then install and adjust a pressure regulator to the target of 600 to 650psi. (Max 725) 

Gauge can be removed for day to day use

Once you know your settings are correct you may remove th egauge for day to day cleaning

Keep the gauge handy should the pressure washer used be swapped out so you can test again

Item #:159-135
Regular Price: $2,343.60
$2,196.35
Item #:159-1410
Regular Price: $152.05
$142.10