Welcome to J. Racenstein Co  (201) 809-7500  |   Q & A  |   Help  |  Catalogs  |  About Us  |  Events
Free Shipping on Orders over $50, look for Weekend Savings
  • ProTool Counter Rotating Solar Brush 16in   with Floating Brush System
  • ProTool Counter Rotating Solar Brush 16in   with Floating Brush System Image 1

Videos

ProTool

ProTool Counter Rotating Solar Brush 16in with Floating Brush System

Quick Overview

  • Minimum Requirements: 435 PSI (30 BAR)
  • 2.3 gallons per minute consumption 9 LPM
  • 725 PSI (50 BAR) maximum working pressure
  • Automatic adjustment on the panel, thanks to the floating system

Show More
Item #: 159-132  UPC : 00669893027251  MPN : HSRN-New

$514.20

$588.00

 
 
 Available Mid October
This is an obsolete Item

Counter Rotating Brush Water powered.

Used to clean Atrium Glass, Solar Panels, glass Porticos, Metal Roofs, Granite walkways. This brush will help to make quick work of cleaning glass and other smooth surfaces that approach horizontal

Managing water pressure is important
  • Minimum Pressure required is 290psi (20 Bar)
  • Maximum Pressure allowed is 725psi (50 Bar)

Not for use with Hot water, Max 105 Degrees F (40 C)

For Pressure washing sizing the Brushes 2 tips (#3.5) are the same as a #7 tip in your Pressure washer

We recommend the use of an inline pressure gauge to monitor pressure..

A Small Pressure Washer 2.5 GPM at 3000psi is all you need to run this water powered brush.

Do not run a larger pressure washer with this brush at it will damage it.

Connecting to a Extention Wand

When using an Extension Wand that has an M22 Male Tip on the  end. Then to attach the water poered brush be sure to order a Female to Female M22 Fitting to connect the brush to the extension wand 

Regulator and Gauge

Use a Pressure Gauge to undestand the pressure at the brush

Install the Gauge on the water connector on the brush

Test Run your your pressure washer and supply water to the brush from your running pressure washer the PSI should be between 290 psi and 725 psi.

One you have your system setup at the correct pressure ytou can remove and store the gauge for future testing

Alway test again after a pressure washer has been worked on or should a different pressre washer is put in place to power the brush

NOTE:

If your pressure Washer is running the brush at more that 725PSI then immediatly stop the water flow.

You can try a smaller pressure washer or install and adjust a  Pressure Regulator to set the pressure to the suggested 600 to 650 psi to run the brush. (Max 725psi)


Regulator and Guage not included

Testing and Setting Water Pressure 

If your pressure washer is to big you will need to usea Pressure Regulator to control the Pressure - Target 600 to 650 PSI.

Here the gauge is installed 

Attached to the Pressure washer and run the brush, ig you are between 300 and 650psi you are good to go.

Attach a Pressure Regulator and Test, Set PSI

If the pressure is more than 725 PSI then install and adjust a pressure regulator to the target of 600 to 650psi. (Max 725) 

Gauge can be removed for day to day use

Once you know your settings are correct you may remove th egauge for day to day cleaning

Keep the gauge handy should th epressure washer used be swapped out so you can test again

The user manual is available at this link:

Counter Rotating Brush User Manual


Counter Rotating Brush for Solar Panels 

Item #:159-135
Regular Price: $2,702.50
$2,370.80
Item #:159-1321
Regular Price: $311.45
$268.40